Primary tabs
COAL REMOVER
SKU::RXSOL-22-2201-050
A powerful penetrating mixed chemical products to remove heavy coal deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems.
It is free from hydrocarbon solvents, non flammable and biodegradable.
Biodegradable / Non-Toxic / Non-Pollutant.
VERY Cost effective.
Recommended to use spray equipment.
The use of hot water will greatly enhance the effectiveness of the cleaning and should be utilized whenever possible.
• Use cold - no heating required.
• Easily dissolves deposits containing carbon , polymer resin etc.
• Economical to use.
• Scraping not required.
• Non- flammable.
• Helpful for burner tips, fuel injectors and all components fouled by carbon, resin or varnishes.
• Cleans oil side of fuel heaters, oil coolers, etc.
• Can be used for cleaning of : -Fuel Oil Filters - Pistons - Piston rings - Valve cage
Directions for Use and Dose Rates
Soak Method:-
It may be used concentrated or diluted with water, depending on the degree of contamination, the surface area to be treated, the desired degree of cleaning and the available downtime.Actually, the user is the best one capable to regulate the quantity and concentration to be used for the situation at hand.In any case, when the accumulation is not heavy, a 50% solution with water must be used. Otherwise,RXSOL-22-2201. can be used undiluted especially when deposition is heavy and hard spots persist.
Cleaning Procedure
Conventional cleaning methods such as a brush,hard sponge, thick and hard broom and /or a mop can be used on heavy duty and hard stain deposits.Note that for heavy accumulations the cleaning procedure might be necessary to be repeated until the results are satisfactory. Furthermore, is important to keep in mind that 1 litre of RXSOL-22-2201 is sufficient to cover a surface area of 8–10 square meters.
NOTE ::: -- Let this product soak into the surface for 30-45 minutes. Then using a high-powered spray washer blast the surfaces until the stains and discoloration is gone.
Note:-
• Cleaning time will vary depending on the extract nature and thickness of deposit to be removal.
• Stubborn deposits should be scrubbed to assist the cleaning operation.
Your local RX MARINE INTERNATIONAL representative will work with you to design the optimum concentration & procedure for your system.
RXSOL-22-2201 should be mixed with fresh water to form a solution of 10-30%, depending on the extent of scaling. After using RXSOL-22-2201 it is essential to thoroughly rinse all metal surfaces at least once with a 0.5% solution of Alkalinity Control in fresh water. This solution should be circulated for 2-4 hours or until an acceptable pH value is obtained. This will neutralize any remaining acidity & passivate steel surfaces.
**Read the Material Safety Data Sheet before using this product.**
Other Valuable Hold Cleaners :::
Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020, Part No.- RXSOL-22-2202-050
Tips for general cleaning of Cargo Holds.
1st step is Manual Cleaning: First of all try to remove all loose / deposited cargo, live & dead insect & weevils from Holds frames, beams, girders, and other structure by manual swiping or air blown pressure method. This step not only help to consume less clean requirement but also loose debris cargo materials can mess entire surface with contact of a liquid solution, further can kill more time.
2nd Step is Inspection: After following the 1st method of manual cleaning try to remove loose rust/paint skin from the metal surface, For this step Metal Clean Bright Rust remover and paint remover can save more time other than manual scraping cleaning methods. As we observe that only 25 ltrs to 50 Ltrs of Metal Clean Bright is sufficient to complete this step of cleaning of Bulkheads, upper and lower hopper spaces, underneath of Hatch Covers and the tank top.
3rd step is for Wise Decision for selection of suitable cleaner : Then apply selected hold cleaning agent like ALKAATUFF Ship Hold Cleaner, hold brite, Alkaclean, Coal Remover, Cement remover, Hodwash, Rock Phosphate cleaner, HBI cleaning agent, Sodium Hypo, Muriatic Acid, Citric Acid, Fore and Aft, PCS hold cleaner, Teepol and other detergent cleaners. Before selection of any cargo hold cleaning detergent understand chemical property of cleaner and actual requirement, For example, if cargo is lime then Lime Remover can works better then ALKAATUFF Ship Hold Cleaner. As lime contains alkaline component when it comes in contact with moisture, solidification starts which becomes hard solid deposition. The hard solid lime deposit can be easily broken in to lose muddy mass by application of RXSOL LIME WASH, Its chemical formula is effectively neutralized alkaline content of LIME. Similarly, cement remover, Coal Remover and other specialized hold cleaner contain specialized materials to work fast on specific cargo.
4th step is for Bilge Area: Bilge covers should be cleaned of any cargo residues. Check each and every drain hole should be open and Bilge cover must be covered with BURLAP, not with plastic or other watertight materials ( for ready reference pl. click here ). And Bilge tank should be cleaned and odour free by using suitable detergent with deodorizer and antibacterial properties. Chemically ppm level of potassium permanganate can play best role which is not only disinfected surface but also can deodorize the tank.
Available stock at Kandla, Mundra ( Gandhidham ), Mumbai, JNPT - Nhava Seva, Goa, Manglore, Vishakhaptnam - Vizag, Gangavaram, kakinada, Chennia - Ennore, Tuticorin, Kolkata - Haldia, Paradip - INDIA and All middle east port - Dubai, Sharjah, Fujairah, Abu Dhabi
#COALremoverSupplier_Mumbai
#COALremoverSupplier_Dubai
#COALremoverSupplier_Muscat
#COALremoverSupplier_Mundra
#COALremoverSupplier_Kolkata
#COALremoverSupplier_Paradip
#COALremoverSupplier_Visakhapatnam
COAL REMOVER ship hold cleaning detergent chemicals manufacturer and supplier in Mumbai, Kakinada, Mundra, Gangavaram, Kandla, Hazira, Visakhapatnam, Surat, Gujrat, Haldia Buzbuz, Paradip, Ennore Chennai, Fujairah, Sharjah, ajman, Abudhbai, Dubai, Gulf, Ruwi, Barka, Muscat, Sohar, Oman, Nairobi, Kenya, Sudan, Yemen
Recommended to use spray equipment also can be apply by hand spray method.
Safety And Handling :-
“RXSOL-22-2201” is completely safe to handle, being non-toxic & non corrosive.As with all chemicals general safety and handling procedures apply. Avoid contact with eyes as irritation may occur. Do not take internally. In case of contact with eyes, flush eyes immediately and cupiously with clean running water for 15- minutes and seek medical attention.
