Primary tabs
Alkali Cleaner RXSOL ORG - 6
SKU::RXSOL-20-2059-027
RXSOL ORG 6 , ALKALI CLEANER is Eco - Friedly and Non Hazardous degreasing cleaner for ferrous and non-ferrous metals.It is an excellent blend of powerful surfactant to remove of soil,dirt, rust, Oil & Grease , carbon , light paint etc, from Ferous & No Ferous alloys and its surface. The Product has a long life with very good cleaning effect. It is alkaline in nature without any complexing agent and cleans the surface totally making it active and bright. This product is fully soluble in water , in all proportion , and it not produce vapour of any kind.
RXSOL-20-2059-025 is an all purpose degreaser for cleaning of Oil and Sludge with emulsifiers. It is an excellent blend of powerful cleaner and emulsifying inorganic products .Specially designed for engine room, degreasing of metal and cargo tank cleaning .Main feature of this product is, it finally dissociate slop emulsion to separate oil and water and inhibit calcium, magnesium, and silica scale and also help corrosion control by dispersing iron oxide.
Alkaline cleaning agents contain strong bases for mainstay of industrial cleaning. Cleaners are many in number and vary in type and formulation. Working solutions of alkaline cleaners have proprietary alkaline cleaners and specifically formulated chemical blends. This product is classified as Alkaline Degreasers and Cleaners.
ALKALI CLEANER RXSOL ORG 6
RXSOL - 20-2059-025
( OIL, GREASE, & SLUDGE REMOVER )
Product Description & Application
- Prior to all kind of plating.
- Prior to Blackening and Phosphating.
- In a continuous Automatic strip, wire or coil cleaning purposes.
Oil and Sludge remover
RXSOL-20-2059-025 / 050 is recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. It may be applied by brush, spray, immersion, soaking, or any other conventional means.RXSOL-20-2059-210 is used neat. Allow a residence time of at least 20- 45 minutes where possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed to separate in a holding tank for atleast 3-5 hours before passing through an oily water separator.
Tank Cleaning Sludge/ Lube Oils / Slope-Black Oil
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a temperature between 65°C & 80°C then stripped constantly and transferred to a holding tank for separation.The time for this will vary depending on amount of RXSOL-20-2059-210 used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-2059-210 on tank surfaces to be cleaned, left for at least 30 minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.
- Prior to all kind of plating.
- Prior to Blackening and Phosphating.
- In a continuous Automatic strip, wire or coil cleaning purposes.
Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended, where as medium contamination dilute 1:10, And for heavy contamination neat RXSOL-20-2059-025 / 050 is suggested to use.
Dosage:- Dose rate and results will vary depending on amount of contamination and deposit of oil grease, Soil etc . For light contamination dilution with water up to 1:20 is recommended, where as medium contamination dilute 1:10, And for heavy contamination neat RXSOL-20-2059-025 / 050 is suggested to use.
OPERATING CONDITIONS
| FERROUS | NON-FERROUS | |
| Concentration | 50-80 g/l | 25-30 g/l |
| Temperature | 65-80ºC | 65-80ºC |
| Time | 2-5 Mins. | 2-5 Mins. |
BATH MAKE UP
- Fill the tank approximately 2/3 rd of the tank with warm water.
- Add the required amount of RXSOL-20-2059-025 / 050 and stir till Homogenous homogenous.
- Fill the tank to working level with water and heat to operating temperature.
MAINTENANCE
The concentration of the bath can be best determined by simple acid base titration using phenolphthalein as indicator.
Titrate 5ml of sample solution against 1N H2SO4. The concentration of the cleaner can be known by the formula given below : Calculation : Conc. = R x N x 15 Where, R = Burette reading N = Normality of H2SO4.
Any grease that collects on the surface during operation should be removed in order to avoid resoiling of components during lifting out of the solution. The loss of water by evaporation has to be made up from time to time. If the solution acts slowly after some period of usage and some components are no longer sufficiently cleaned, the bath should be replaced with the new one.
EQUIPMENT
Plain steel tank is recommended. Heater made of steel or quartz can be used for heating purpose
CONTROL
The cleaner solution can easily and effectively be controlled by removing floating oil over the surface either manually or by means of circulating pump and an oil trap regularly. The concentration of the solution can be maintained by analysing the alkalinity of the solution by simple titration with standard acid using Phenolphthalein as an indicator.
Another Procedure of use for clean small spare Parts :- RXSOL-20-2059-025 / 050 is recommended for cleaning & degreasing of metal pipe, spare parts . It may be applied by brush, spray, immersion, soaking, or any other conventional metosd. RXSOL-20-2059-210 is used neat. Allow a residence time of at least 20- 45 minutes where possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed to separate in a holding tank for atleast 3-5 hours before passing through an oily water separator.
Tank Cleaning Sludge/ Lube Oils / Slope-Black Oil :
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a temperature between 65°C & 80°C then stripped constantly and transferred to a holding tank for separation.The time for this will vary depending on amount of RXSOL-20-2059-025 / 050 used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-2059-025 / 050 on tank surfaces to be cleaned, left for at least 30 minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.
Characteristics:-
High penetration & emulsification , Reduces down time.
Low toxicity, non -corrosive. Highly effective, economical solvent cleaner.
For cleaning of machinery parts, bulk heads, decks, bottom plates & any oil/grease dirty areas.
Used for cargo tank cleaning of mineral oils and petroleum based chemicals, Sludge etc .
CAUTION : RXSOL-20-2059-025 / 050 is alkaline in nature and contact of the skin or eyes should be avoided.
NOTE : The data set forth in this Bulletin is believed by RX Marine International to be true, accurate and complete but is not guaranteed. Our sole warranty is as stated in our standard Terms and Conditions of Sale. We cannot warrant out customers will achieve the same results from any bulletin because we do not have control over the condition of use; nor can we assume any responsibility for our products in a manner which infringes the patents of third parties.
|
Appearence |
Clear (Raw material depended colour of the effectively will , however not be impaired .) |
|
|
|
Density |
1.48 - 1.50 @15°C |
|
|
| Total Alkalinity % by Mass | 50% Minimum | ||
|
Flash Point |
Non Flammable |
|
|
| Foaming | Non Foaming | ||
|
Solubility |
100 % soluble in cold and hot water with any ratio. |
||
|
Compatibility |
|
|
|
|
Metal |
No known effect |
|
|
|
Rubber |
Do not use with natural rubber compounds |
|
|
| Shelf Life | 18 month from Date of manufacturing | ||
Alkali Cleaner supplier in DLW, Varanasi.
Alkali Cleaner manufacturer and supplier in Varanashi, Mumbai, Mughalsarai, Luckhnow, Kandla, Gandhidham, Kolkata, Chennai, Vizag - Visakhapatnam - INDIA.
