ORG Clean MC 103 Membrane Cleaner
It is a low pH, liquid formulation designed specifically to remove metal hydroxides, calcium carbonate, and other similiar scales from reverse osmosis (RO), nanofiltration (NF), microfiltration (MF) and ultrafiltration (UF) membranes. This highly effectiv
ORG Clean MC 103 (Membrane Cleaner) Liquid is a low pH, formulated specifically to remove metal hydroxides, calcium carbonate, and other similiar scales from reverse osmosis (RO), nanofiltration (NF), microfiltration (MF) and ultrafiltration (UF) membranes. This highly effective product provides superior cleaning resulting in longer system running time.
Acidic powerfull cleaner, non-foaming (pH1.6).
ORG Clean MC 103 (Membrane Cleaner)
- Suitable for use wtih all thin film or cellulosic membranes.
- Buffered to maintain an effective pH over a range of dilutions.
- Cleaner for ease of mixing.
- No adverse effects with repeated use.
- Enhanced performance at elevated temperature.
- Low foam formulation.
TYPICAL APPLICATIONS ::: 25 to 38 Grams per Ltr of Water, Solution can be heated to increase cleaning effect.
During the operation of a membrane separation system, dissolved solids in the incoming water can concentrate up to a level where they begin to precipitate on the membrane surface. Scaling from hardness and metal salts found in most unsoftened water supplies impedes the flow of water through the membrane. This can result in unacceptably low production, high operating pressure, or an excessive pressure drop in the system, which may lead to irreversible membrane damage. Additionally, the accumulation of scale next to the membrane surface can increase the amount of dissolved material passing through the membrane, resulting in product water of unacceptable quality. Before the scale accumulates to a level where product water declines, or membrane damage can occur, it should be removed through clean-in-place (CIP), off-line cleaning. Indications of
the need for cleaning include a significant decrease in normalized permeate flow, a significant increase in pressure drop across the system (or individual stage), or an increase in the normalized salt passage, so that product quality is unacceptable. Your RX MARINE representative can assist you with monitoring your system and determining when cleaning is advised.
ORG Clean MC 103 (Membrane Cleaner) contains a blend of solubilizing and complexing agents designed to specifically remove calcium carbonate and metal hydroxide-based scales from the surfaces of a membrane. Used in tandem with an alkaline cleaner for organics and particulate removal, regular cleanings with ORG Clean MC 103 (Membrane Cleaner) helps to preserve the life of your membranes. Depending on the nature of the fouling, a soak period may be necessary for optimum results. Consult your RX MARINE for details.
Feed System - This product should be used in conjunction with membrane cleaning equipment supplied by the manufacturer of the membrane system. If such a system is not present, contact your RX MARINE representative for information on fabricating or obtaining a cleaning system.
Dilution - The product must be diluted prior to introduction into the membrane system. The recommended dilution for this product is one pound (0.45 kg) of ORG Clean MC 103 (Membrane Cleaner) per 5 gallons (19 L) of water (approximately one gallon [3.8 L] of ORG Clean MC 103 (Membrane Cleaner) for each 50 gallons [189 L] of water).
Materials Compatibility - Corrosion-resistant equipment, such as PVC, should be used for the storage and preparation of this product. Pumping materials coming in contact with concentrated or diluted products should also be corrosion resistant.
ORG Clean MC 103 (Membrane Cleaner) is a liquid material, available in a wide variety of customized containers and delivery methods.Contact your BetzDearborn representative for details.
GENERAL CLEANING INSTRUCTIONS
The following general cleaning procedure can be followed. For the optimum cleaning procedure for your system, contact your BetzDearborn representative.
- Inspect cleaning tank, hoses, and cartridge filters.Clean tank and flush hoses if necessary. Install new cartridge filters.
- Fill cleaning tank with RO permeate or DI water. Turn on agitator or tank recirculation pump.
- Slowly add ORG Clean MC 103 (Membrane Cleaner) to cleaning tank (1 gal [3.8 L] of product for every 50 gal [189 L] of water) and allow to mix thoroughly.
- Check solution temperature. If solution temperature is lower than recommended level, adjust heating control to provide optimum temperature. If manufacturer’s recommendation is not available, contact your RX MARINE representative.
- Check solution pH. The solution pH should be 2.5-3.5 or as recommended by the membrane manufacturer. If pH is too low, adjust pH upwards with NaOH, or other chemical as recommended by the membrane manufacturer. If pH is too high, adjust with hydrochloric acid.
Circulate solution through one stage at a time in the direction of feed flow for 30 minutes. Circulate at the flow rate recommended by the
membrane or system manufacturer. If manufacturer’s recommendation is not available, contact your BetzDearborn representative. Pressure
should be low enough so that no permeate is produced during cleaning, but always less than 60 psig (4.2 kg/cm2). In cases of heavy fouling, the first return flow (up to 15% of the cleaning tank volume) should be diverted to drain to prevent redeposition of removed solids. For optimum results, each stage must be cleaned separately in a multistage system.
- If the first stage cleaning solution becomes turbid or discolored, dump the tank and prepare a fresh cleaning solution before proceeding. If solution pH or temperature moves out of the recommended range, a new solution should be prepared. In any event, a new cleaning solution should be prepared for each stage.
- Rinse with RO permeate at 20°C (68°F) minimum before returning system to service.
- When returning unit to service, divert product water to drain until any residual cleaning solution has been rinsed from system.
A Material Safety Data Sheet containing detailed information about this product is available upon request.
ORG Clean MC 103 Membrane Cleaner is suitable for use with all polyamide, polysulfone and thin film, composite membranes. During uses of membrane cleaning chemicals always be remember that In cases of heavy fouling, the first return flow should be drain out side, not in a circulation tank, this will helps to prevent redeposition of removed solids. In multi-pass systems, best results will be achieved if each pass is cleaned separately.
The solution should be discarded if it becomes turbid or discolored by removed material. A fresh solution should then be prepared before cleaning additional passes.
|Physical State||Powder, solid, Liquid, Granules, Crystals|
|Usage||RO MEMBRANE claning chemicals Industrial, Commerical|
|Grade Standard||Technical Grade|
|Packaging Size||10 kg / 20 Kg|
pH adjusted to 3.0+ 0.5
Highly effective at ambient temperatures
Contains no surfactants and is quickly rinsed away
ORG Clean MC 103 Membrane Cleaner Contains organic acids, detergent builders and chelating agents to make cleaning easily and effectively.
ORG Clean MC 103 Acidic Membrane Cleaner powder manufacturer, exporter and supplier in Mumbai, Kolkata, Chennai, Muscat - oman, Fujairah - UAE, Sharjah, Ajman, Abudhabi, Diera Middle East - UAE, Visakhapatnam, Gandhidham, Surat, Navi Mumbai, Taloja MIDC, Pune, Nashik
ORG Clean MC 103 Membrane Cleaner / Floclean MC3 : Easy-to-use all-in-one acidic cleaner for removing inorganic scale and metal oxides
Membrane ALKA Clean RXSOL ORG -10 ( Powder ) / Floclean MC11 : Easy-to-use all-in-one alkaline cleaner for removing silt, organics, and biofilm
Biocide Antimicrobial / Flocide 380 : Biocide/sanitizer for RO systems for preventing the fouling from fungi, yeast, bacteria, and biofilm
Membrane Cleaner RXSOL- 3304 / Flocon MC30 : Specialized super-strength cleaner for iron and metal oxides
Membrane ALKA Clean RXSOL ORG -10 ( Powder ) / Flocon MC50: Specialized super-strength cleaner for silica and CaSO4 scale
ORG Clean MC 103 Membrane Cleaner is balanced acidic low pH powder / crystal product specialize to remove metal hydroxides, calcium carbonate and other similar scales from polyamide, polysulfone and thin film, composite membrane surfaces.
ORG Clean MC 103 Membrane Cleaner is advanced, high strength powder to clean Membrane from fouling.