Primary tabs
Rust Stain Remover RSR ECO
SKU::RXSOL-13-1096-020
Eco-friendly product specially designed for removal of rust from any steel surface area and rust stains from brass, copper, stainless steel, aluminum, wood and ceramic surfaces. Also acts as a surface brightener.
It is a heavy duty and concentrated liquid blend of surfactants & organic compounds containing rust penetrating agents , solubilizer and inhibitors. Acts as rust proofing agent before the application of paint or coatings. It is non-flammable. Prevents further rusting.
MARINE - Rust Stain cleaner Ecofriendly ( foaming nature )
This product is very effective as a spot cleaner after cleaning fats and fatty acids , can be used on painted surface
A superior heavy duty and highly Concentrated liquid blend of surfactant & organic compound containing rust penetrating agent, solubilizer and inhibited organic acid with ionic and non ionic emulsifier.
In most cases RXSOL-13-1096-025 is applied by brush full concentrated for heavy stains, or diluted with 10-50% with fresh water for light strains and left to react for 5-10 minutes. Smaller objects can be soaked in plastic container. After cleaning, rinse items thoroughly with a water jet.
Paintwork
Dilute RXSOL-13-1096-025 , 1 liter of product to 2-10 liters water, apply the solution by brush or spray using plastic equipment and leave to soak for 10-20 minutes. Rinse off using a powerful water jet with a brush, if necessary.
R 34 : Causes burns.
S 26 : In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
Do not mix with other chemicals.
The information provided in this data sheet has been compiled in accordance with the requirements of the Chemicals (Hazard information and packaging) Regulations 2002 (CHIP 3).
This data sheet does not constitute an assessment of the workplace risks as required under the provisions of the Health & Safety at Work act and the Control of Substances Hazardous to Health (COSHH).
FOR TANK CLEANING
RECOMMENDATION : 0.2% TO 100%
FIELD :-
specially designed for removal of rust from any steel surface area and rust stain from Brass , Copper , S.S wood , ceramic and aluminium surfaces , painted or not . And act as surface brightner.
Procedure for Use :-
- RXSOL-13-1096-020 is highly concentrate
- Dilute in water (always use plastic jar and RXSOL-13-1096-020 should be added to water never add water to (RXSOL-13-1096-020.)
- Surface should be sound clean and free from oil, grease, dirt etc.
-
Diluted materials apply on rusted area for 15 to 20 minutes then wash off with water repeat if necessary.
(For stubborn rusted stains.)
NOTE :-
For steel surfaces; remove oil, grease and old paint. Wet down entire surface with neat RXSOL RSR ( RXSOL-13-1096-020 ) and allow to dry. Second wash may be necessary. Surface should have a grey/white appearance when the RXSOL RSR is dry. Steel surfaces will have a resistance to rust and will render a good base for paint.For removal of rust stains on painted surfaces and wood, RXSOL RSR should be applied at full concentration for heavy stains, or diluted to 20-50% for light stains. Allow to soak for 15 to 30 minutes and wash off with water. A second application may be necessary to remove the stubborn stains.
Spraying Direction :-
Using an empty / clean 210 liter drum, fill with 190 liter of fresh water and add 20 liters of RXSOL RSR This makes a 10% solution, which can be sprayed onto areas in coated tanks where rust stains are showing and over actual rusted areas. Once spraying is completed, wait 20-30 minutes and fresh water rinse with lots of water, if possible use butterworth machines for a more efficient result. This method can be used in stainless tanks to “freshen up” the look of the stainless materials. Make sure to rinse the tank very well, as residual detergent within the RXSOL RSR will show up in a Wall Wash.
Injection – Not suitable.
Re-circulation :–
When hand spraying is inadequate (too much area to cover), prepare a 2% - 5% solution in the tank using fresh water, heat solution to 50o C, then circulate the solution through butterworth machines for 3 x 45 minutes drops minimum. When using fixed machine recirculate for a minimum of 3 cycles. Rinse out the tank using hot seawater 85o C for 2 hours making sure that there is no form remaining in the water at the pumpstack drain cock. After the hot wash, the tank must be rinsed with fresh water and dried.
* If the mixture is allowed to overheat, it will soften epoxy / phenolic coating.
* Use a strainer at the pumpstack when circulating any solution.
Tank Lining – Stainless / Epoxy, Phenolic
It is a superior heavy duty and highly concentrated liquid blend of surfactants & organic compounds containing rust penetrating agents , solubilizer and inhibitors. Acts as rust proofing agent before the application of paint or coatings. It is non-flammable. Prevents further rusting. * Cleans and brightens aluminium and copper.
* Removes rust stains without risk to paintwork.
* Safe on most common metals
specially designed for removal of rust from any steel surface area and rust stain from Brass , Copper , S.S wood , ceramic and aluminium surfaces , painted or not . And act as surface brightner.
Characteristics :-
- Non-flammable.
- Prevents further rusting.
- Economical , cost effsctive.
- Surface brightening
- Protects and maintains from corrosion
- Acts as rust proofing agent before the application of paints or coatings.
- It doesn’t affect rubber and plastic compounds
- removes corrosion of all metals
- excellent cleaner to remove contamination of fats and salts Marine application for trains, busses, tank containers and ship tanks
- odourless, so it can be used in enclosed space
- suitable for manual cleaning as well as high- and low pressure systems
Note :-
When cleaning aluminium, brass & copper flush with water upon completion of cleaning immediately Warning : In case of contact with skin , wash immediately with plenty of water. Use chemical resistance PVC gloves for skin contact and also use face mask for eye and face protection.
Read the Material Safety Data Sheet before using this products.
PRODUCT PROPERTIES :
| APPEARANCE | Clear liquid | |
| DENSITY | g/cm3 at 15°C: 1.2 | |
| pH | 10% solution 1.5-2.5 | |
| COMPATIBILITY | ||
| METAL | Concentrate and long touch may corrode. | |
| RUBBER | No known effect | |
| PACKAGING | Order No. RXSOL-13-1096-020 | Size (in litres) 25 , 35 , 210 |
#RustStainRemoverinOMAN
#RustStainRemoverinSOHAR
#RustStainRemoverinMUSCAT
#RustStainRemoverinDUBAI
#RustStainRemoverinSharjah
#RustStainRemoverinUAE
#RustStainRemoverinINDIA
Rust Stain Remover RSR manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai UAE, Muscat Oman, Kenya Africa. Get the best quality of Rust Stain Remover RSR at a competitive price from us. We have ready stock of Rust Stain Remover RSR in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.
